AccessTUNER Race gives the control you need, when you need it.

AccessTUNER Race Is Currently Available for:

Subaru:

• Impreza WRX (2002-2009)
• Impreza WRX STi (2004-2009)
• Impreza 2.5 GT (2009)
• Forester XT (2004-2009)
• Legacy GT (2005-2009)
• Legacy Spec B (2005-2009)
• Outback XT (2005-2009)

Mitsubishi:

• EVO VIII (2003-2005)
• EVO IX (2006-2007)
• EVO X (2008)
• EVO X (2008) JDM, ADM & EDM

Mazda:

• RX-8 (2004-2008)

ATTENTION

AccessTUNER Race is not meant for beginners. It is designed to be used by experienced engine tuners.  Use of AccessTUNER Race by those that do not have adequate tuning experience could generate catostrophic results.

Pre-Installation

The AccessPORT comes with the most up-to-date software and map files available at the time of shipment. However, it is possible that updated software and/or map files have been made available since the time of shipment. Therefore, the recommended procedure is to connect the AccessPORT to the AP Manager software and download the latest software and map files for the target vehicle.

Getting Started

1. Insert the key into the vehicle’s ignition and leave it in the OFF position.

2. Locate the Test Mode connectors. Impreza and Forester models will have this located under the driver’s side dash to the left of the steering column. The Legacy and Outback models will have this located on the passenger side. With the connectors located, enable Test Mode by plugging the two
connectors into each other.

3. Connect the small end of the provided USB cable to the mini-USB port on the back of the OBD connector.

4. Plug the OBD connector into the vehicle’s OBD-II port.

5. Plug the large end of the USB cable into the standard USB port on the underside of your AccessPORT. At this point the AccessPORT will power up and present the installation menu after approximately 20-30 seconds

6. Select [Install] from the AccessPORT menu by pressing the [OK] button to proceed with installation. Below is a diagram of the AccessPORT’s keypad function.

IMPORTANT!

Before installing the AccessPORT on the vehicle, it is important to verify that the vehicle is adequately prepared for the installation process. Since the AccessPORT uses the vehicle’s battery for power and the ECU reprogramming process requires adequate battery power as well, it is critical to verify that the vehicle’s battery has a good charge. This can be done through the use of a battery charger/conditioner or by driving the vehicle for a period of time prior to installation to allow the alternator to recharge the battery. Furthermore, please ensure that all in-car electronic devices are turned off to reduce power draw on the battery. This includes car stereos, video screens, GPS units, radar detectors, interior and exterior vehicle lights, and any other electronic device that uses the car battery for power.

Does COBB AccessPORT support my car? Why should not I make it sure from the list Below:

Supported Subaru cars List

• 2004 – 2007 Subaru Impreza STI
• 2008 – 2009 Subaru Impreza STI
• 2005 – 2009 Subaru Legacy GT (MT & AT)
• 2005 – 2009 Subaru Outback XT (MT & AT)
• 2004 – 2008 Subaru Forester XT (MT & AT)
• 2009 Subaru Forester XT (MT & AT)
• 2009 Subaru Forester XT (MT & AT)
• 2008 – 2009 Subaru Impreza WRX (MT & AT)
• 2002 – 2007 Subaru Impreza WRX (MT & AT)

Supported Nissan cars List

• Nissan 350z

• Nissan GT-R (R35)

Supported Mazda cars List

• Mazda RX 8
• Mazdaspeed 3
• Mazdaspeed 6

Supported Mitsubishi cars List

• Evo (2003 – 2007)
• Evo X (2008)

Supported Infinity cars List

• Infinity G 35
• Infinity G 37